How to Remove Dents from Car Door Panel(3 Easy ways)

How to Remove Dents from Car Door Panel(3 Easy ways)

As soon as your car takes a dent, she looks older and worn out. This has an impact on the value of your vehicle, as well as on your own feeling of having a car that is no longer quite perfect. If you want to deboss your car yourself, there are some methods that you can easily use at home. In this article, we will discuss specifically dent on a car door panel. Thus, read the article and know about how to remove dents from car door panel?

Caution, however: if you are not a handyman or if you do not spur of what you are doing, you could worsen the impacts.

How to Remove Dents From Car Door Panel?

There are two types of dents on the door panel of a vehicle.

i- Big Dent/bumps

ii- Light Dent

Big Bumps on a vehicle’s door panel

If you have a big enough dent on your car door, you can get a dent kit to fix it. Of course, it’s not exactly cheap, but then you will have the right equipment to do the repair, which is alfa and Omega for a satisfactory result.

This works as follows: You stick one or more cylinders on or around the bump. Then you will use your toolbox, specially designed for this task, to ”push back” the bump and correct it.

An alternative is to do about the same thing, with pieces of wood sticking to the bump, but you will still need to have the right glue, which dissolves easily after use and leaves no traces on the paint of the bodyshell.

Light Dents on Automobile’s Door

Fixing a light dent in your car door doesn’t have to make a hole in your wallet. You could eliminate these dents yourself, without special tools.

There are many ways to remove small dents, depending on the tools you have. You have two examples here :

The Vacuum Cleaner/Plunger Method to Fix Bumps

First, take 3 to 4 liters of hot water and pour on the door of the car with dents. After pouring all the water on the door of your car, take the plunger from your toilet, press it carefully on the dent, and then pull it. You may have to do it several times to succeed.

Before placing the plunger, make sure it is clean, and spread a lubricant, such as a vaseline, on its edges in contact with the body, so that you can easily remove it.

The Hammer Method to Remove Bumps from Car Door Panel

If you can access the metal plate from the inside, you also have the possibility to hit the bump to make it shrink. This is the simplest method, but you should always proceed with caution.

Remove Dent with Hammer

Take a metal plate and cover it with a cloth, before placing it over the hump from the outside, to preserve the paint. Then you can hit the dent carefully from the inside, and after a few strokes, the body should be debossed.

There is no guarantee that the method will work as expected, and the result may be permanent marks on the bump. If it is a rather new car, you will probably prefer to use your insurance, in order to be sure of a perfect result.

The Hairdryer Method To Remove Dents

The metal expands and tightens during temperature variations. Not the ordinary little temperature variations of the daily weather, but, through extreme temperatures, you can produce miracles and you can cover up the dent on the car door.

You can Read More About: List of Car Problems with Solutions

In order for this to work on dents, you will need to heat the metal in the dent to the highest possible temperature, without damaging the paint, then cool it to the lowest possible temperature just after.

You will first have to use a hairdryer and then spray “something very cold” on the bump. A compressed air spray, which turns upside down, should do the trick.

After a few tests, the dent should shrink again, on its own, or with the help of slight strokes around it, in order to repel the metal. Just follow the steps which are going to be mentioned below;

You Will Need

  • A hairdryer;
  • Strong rubber gloves;
  • Dry ice or compressed air;
  • Aluminum foil (if you are trying the dry ice method).

First Step: Heat the Dented Area

Put the hairdryer on “medium” or “hot” and apply heat to the damaged area. Keep the dryer five to seven centimeters from the surface of the car to prevent paint damage. Apply heat for about a minute or until the area becomes warm to the touch.

Second Step: Isolate the Affected Area

Place a sheet of aluminum foil on the surface to be treated for insulation. This step should only be performed if you are using dry ice instead of compressed air.

Third Step: Apply Dry Ice or Compressed Air

Be sure to wear heavy-duty rubber gloves to protect your skin from frostbite.

If you are using dry ice, gently rub a piece on the insulated area until you hear the dent coming back.

If compressed air is used, turn the bottle upside down and spray the damaged area until covered by a layer of liquid ice. Liquid ice is formed as a result of the compressed air bottle being sprayed upside down.

Fourth Step: Wait for the Dent to Come Back in Place

A few minutes after applying dry ice or compressed air, you should hear a noise that indicates that the Dent has been repaired.

And that’s all you have to do. Simply remove the aluminum foil or remove any trace of compressed air. Your car will look good.


Leave a Comment